ACTi CAM-5100M Manual de usuario

i Video Transcoder SED-3200 User’s Manual

2-42.2.1 Login Please login with specific Account and Password 1. Account : Type Admin as the default account name. 2. Password : Type

2-52.2.2 Host Setting Please config the LAN setting of this section. 1. Host Name : Enter the domain name for SED-3200 2. Language : Lan

2-6 Value Description 0 1200 1 2400 2 4800 3 9600 4 19200 5 38400 6 57600 7 115200 8 230400 NOTE: Save Reboot is necessary to execute for keeping

2-72.2.3 WAN Setting Please config the WAN setting of this section 1. Dynamic IP Address : Set DHCP mode. 2. Static IP Address : Set Stat

2-86. PPPoE : Point-to-Point Protocol over Ethernet (PPPoE) merges PPP, which is usually used for dial-up connections (e.g. ADSL, Cable Modem). 7.

2-92.2.4 Video Setting Please config the settings to connect Video Server/IP Camera/Other ACTi encoding devices 1. Connect Type : Select Multicast

2-106. Remote Register Port : Port of video registeration. 7. Remote Control Port : Port for video controlling. 8. Remote Streaming Port : Port of

2-112.2.5 User Account Management Please set the users account and password in this section 1. Root : Default Account name is Admin, Password is

2-122.2.6 Port Setting Please config port settings of SED-3200 1. Host HTTP Port : HTTP Port Setting. 2. Host Search Port1 : The port of “Send” p

2-132.2.7 Logo Setting Please config your favorite layout in this section 1. Main window header, please insert an image file (bmp, jpg, gif). Reso

ii SED-3200 2nd May, 2005 This document is copyrighted, 2005, by ACTi Corporation. All rights are reserved. ACTi Corporation reserves the right

2-14 14. : Click this button to apply the setting of this section 15. : Click this button to reset NOTE: Before re-connect to SED-3200, ple

2-152.2.8 System Info This section shows system information and system log 1. System Information : View system information. 2. WAN Status

2-162.2.9 Image Upgrade (1/2) Please upgrade the web server firmware in this section 1. Click to upload firmware. 2. : Click this b

2-172.2.10 Image Upgrade (2/2) 3. Firmware Images File : You can update the Firmware Image version of your device by downloading the latest firmw

2-182.2.11 Factory Default This section allows you to load factory default settings 1. Click to get back to factory default 2 : Click this

2-192.2.12 Save Reboot When you finish all settings, please click Save Reboot and wait about 30 seconds for system save and reboot, until the LAN/WAN

2-202.2.13 Logout Click Logout to logout web server, and will close the IE window.

iii Table of Contents 1 INTRODUCTION ______________________________________________ 1-1 1.1 PACKAGE CONTENTS ______________________________________

1-1 1 INTRODUCTION 1.1 PACKAGE CONTENTS SED-3200 Warranty Card Software CD Terminal

1-21.2 PHYSICAL DESCRIPTION SED-3200 Front Panel 1. Red LED LED Indicating Power or H/W Reset Function 2. Yellow LED LED Indicating when RS-485 Rx

1-36. Terminal Blocks Pin 7~12 Pin 7~10: RS232/422/485. Default mode is RS-485 (if your system needs RS-232 or RS-422, please contact ACTi sales)

2-1 2 INSTALLATION 2.1 Hardware Installation Please follow the following steps to configure your SED-3200 before you install and running ACTi bundl

2-22.1.2 Connect cables The BNC cable for video input, Ethernet cable and power cable are necessary for previewing function. Make sure all cables are

2-32.2 Web Server Configuration Whenever you want to configure the SED-3200,you can access the Configuration Utility by opening the web-browser and